Cutshop CNC.jpg
Cutshop DIY ideas.jpg

Cutshop Trade


With our range of services, we are equally valuable to commercial shopfitters, kitchen or furniture manufacturers or anyone that needs something cut, edged and drilled.

SCROLL DOWN

Cutshop Trade


With our range of services, we are equally valuable to commercial shopfitters, kitchen or furniture manufacturers or anyone that needs something cut, edged and drilled.

Cutshop CNC.jpg

Trade Services


More than just a factory with CNC. Cutshop® is an extension of your workshop - helping you do more work in less time. Cool. Clever. Cutshop®

Trade Services


More than just a factory with CNC. Cutshop® is an extension of your workshop - helping you do more work in less time. Cool. Clever. Cutshop®

Timesaver, moneymaker

'No.8 wire' solutions

This country was built on the backs of people with ingenuity and a ‘can do’ attitude. Cabinetmakers, shopfitters and other tradesmen are dotted all over New Zealand. 

They are practical, hard workers and usually have one thing in common: too little time, too little space. Cutshop® provide services that save precious time, helping businesses grow and work smarter.

That's more time for you at the bach or on the boat!

e-Cabinets

Innovative, clever thinking

Our dynamic e-Cabinet software simplifies the design process. It is easy to use and unique to our CNC machines which means that you can supply us with digital files and be rest assured your job is cut right - first time. 

The software makes our production line faster and more efficient. Most issues can be resolved before the sheet is placed on the cutting bed. The software is available to you, online and at no cost. If you are prepared to invest some time into learning how to use this programme, you will never need to buy kitchen design software again.

Using Cutshop® for cutting and laser / PUR edging will give you more time to promote your business and take on more projects, without stretching your resources. Truly a timesaver, moneymaker.

Our CUTTING standards

Making sure your job runs smoothly

It is important to have set standards to minimise mistakes. Below are some guidelines that will help you set up your files according to Cutshop® standards.

  1. All measurements are to be final sizes.
  2. Our edge taper has a pre-mill on it for a better finish.
  3. A 5 mm off the edge of all sides of the board will not be used as often is damaged and unusable.
  4. A 10 mm router bit is standard cutter used on 3 mm - 20 mm board. 
  5. A 12.7 mm cutter is used for board 21 mm - 45 mm.
  6. Customers can supply their own sheet material (Cutshop® accepts no liability for damaged sheets (scratches, etc.)
  7. Cutshop’s lead time for standard jobs are 4 working days (from receipt of deposit and materials).
  8. Cutshop® does not interpret architect’s plans.
  9. Dimensions of appliances are not accepted (only cabinet dimensions will be accepted).
  10. Cutshop does not liaise with third parties to obtain information to process a client’s job.

A job will not be cut unless the following is specified: 

  • Grain;
  • Material;
  • Edge taping details;
  • Hinge hole details;
  • any other relevent information specified by quote.

Standard cabinet construction 

  1. Sides are joined to the side of the top / bottom rails and the base.
  2. 10 mm knock in feet holes are drilled in the bottom of all base, pantry, draw and corner units.
  3. All adjustable shelf holes are drilled at 32 mm centres.
  4. All construction, draw and shelf holes are drilled with a 5 mm drill.
  5. All edge tape on carcasses and door is 2 mm (unless specified).
  6. Standard kick is 150 mm.
  7. Standard height is 870 mm (including 150 mm kick).
  8. Standard carcass depth is 560 mm (580 mm including doors).
  9. Carcasses are cut from 16 mm white gloss unless specified.
  10. All grain is orientated vertically unless specified.
  11. All hinge holes are drilled at 96 mm centres.
  12. All hinge holes are drilled with 36 mm diameter drill and two 8 mm locator holes (to fit Blum® hinge).
  13. A 3 mm gap is allowed from the top of the door to the top of the carcass and the bottom of the door is flush with the bottom of the carcass, as well as 1.5 mm on each side.
  14. Upper unit backs are screwed into the base.
  15. We will only work from plans or cabinet lists were all dimensions are given (dimensions of ovens and other appliances are not accepted).
  16. Blum® metabox draw runners are used unless specified.
  17. Add standard hardware is Blum® unless specified.
 
Cutshop DIY ideas.jpg

How we work - Trade


We have a choice of delivery options to ensure you receive your goods on time. Give us a call or email us to book a job. You can also visit your nearest Cutshop®.

How we work - Trade


We have a choice of delivery options to ensure you receive your goods on time. Give us a call or email us to book a job. You can also visit your nearest Cutshop®.

BOOKING A JOB

Your job from quote to delivery

  1. We attend to quotes daily, between 3 - 5 pm Monday to Friday (11.30 am on Saturdays).
  2. Our aim is to get your job sorted in 4 working days. If all goes well, we process the job within 4 working days of the materials being received at our depot.
  3. We order the materials within 24 hours of you accepting the quotation and paying a deposit.
  4. You can collect any time between 3 - 5 pm, Monday to Friday.
  5. We can deliver to you at an additional fee. Ask us for a quote.

Deadlines & Timelines

We can process your job quicker for you, but it will cost a bit more. You have the following options:

Standard: 4 working days

FastTrack: 3 working days

Express: 1 to 2 working days

Contact us for a quote or to discuss your project.